Home > Lie-Nielsen Toolworks > Hand Planes > Scraping Planes >

Lie-Nielsen No.212 Small Scraping Plane - Bronze
Lie-Nielsen No.212 Small Scraping Plane - Bronze

Our Price: $175.00

Quantity in Stock:2
Availability:: Usually Ships in 24 Hours
Product Code: A340B

Description Tool Care

Small Scraping Plane

This unusual plane is based on the now scarce Stanley No. 212, which was discontinued in 1934 and brings high prices from collectors. We are pleased to make it available for woodworkers once again.

The almost perpendicular blade makes it ideal for small scraping jobs, producing shavings like the finest lace and leaving smooth surfaces with crisp edges. The blade angle can be adjusted from 75 Degrees to 100 Degrees, enabling it to be set up just right for the particular wood being worked.

It is a favorite among fly rod makers for thicknessing bamboo fly rod sections. We offer an optional Fly Rod Makers Groove, ground 1" wide x .003" deep into the sole of the plane, making it the perfect companion tool to a rod maker's form.

  • 5-1/2 in long x 1-3/4 in wide.
  • Blade is 1-3/8 in wide x 1/8 in thick.
  • Bronze body, 1.60 lbs.

  • Small Scraping Planes

    The Lie-Nielsen Small Scraping Plane is based on the Stanley #212, which was discontinued in 1934. The original has become increasingly hard to find and expensive, but it is the perfect tool to use for many small scraping jobs. We are pleased to make it available for woodworkers once again.

    Blade Sharpening:

    Our Scraping Plane comes with a much thicker blade than the original. This allows the blade to be prepared somewhat differently than other scrapers. We recommend that you hone the blade to a sharp edge like a plane blade and do not use a burr (at least until you get used to using the tool). We have found that our thick scraper blades sharpen easily and produce a better surface with a 45° bevel on the blade. Slightly round the corners of the blade with a stone to prevent them from marking the work.


    If you wish to create a burr, hone the blade, and then clamp it upright in a vise. Using a burnisher, begin by holding the burnisher at about 45° to the blade, working up to 75°. Work the edge until you can feel a distinct ‘hook’ all the way across. Be very careful not to cut yourself on the upright blade. Use of a burr will give more aggressive cutting action, and depending on how consistent you are, turning the burr will require adjustment of the blade angle after sharpening to work best.

    Setting the Blade:

    The blade is inserted with the bevel facing the knob. To set the depth of cut, lay the sole of the tool on a flat surface and loosen the thumbscrew. Press lightly on the top of the blade with your thumb and re-tighten the thumbscrew. Do not over tighten. Usually, this will be enough exposure for a fine shaving. If not, repeat with a slip of paper under the front of the tool. Minor depth adjustments may also be made quickly by lightly tapping the top of the blade with a burnisher or light hammer while the tool is resting on a flat board.

    Adjusting Blade Angle:

    The blade angle should be set about 15° forward of vertical. Try adjusting the angle to find optimum performance in various woods. One way to get it close is to take some test passes holding the blade by hand, varying the angle until it cuts best, then hold the blade at that angle against the side of the plane and adjust the frog to match. The beveled faces of the nuts fit into the countersink on the hole in the post to provide a solid lock. Use: Normally, one pushes the Scraping Plane from the rear with the knob in the palm. The blade is inserted with a bevel facing the knob. It is best to use a light touch, rather than trying to remove too much material at once, or using too much downward pressure. Too aggressive a cut, including too much downward pressure, will result in chatter. You should be taking light strokes. Often it is helpful to scrape at an angle to the grain, then again from the opposite angle. David Charlesworth has a good discussion on the use of scrapers in his book Furniture Making Techniques, Vol. II.

    Toothed Blades:

    We offer replacement blades, as well as toothed blades, of 18 and 25 teeth per inch. Toothed blades are useful, when working extremely difficult woods, to score fibers in a criss-cross pattern before using the regular blade. They are also used to prepare surfaces for gluing, as in veneering, by lightly roughening the surface

Lie-Nielsen No.212 Small Scraper Plane -18tpi Blade Lie-Nielsen Honing Guide Lie-Nielsen No.212 Small Scraper Plane - 25tpi Blade Lie-Nielsen Tool Care Kit
Our Price: $45.00
Our Price: $125.00
Our Price: $45.00
Our Price: $39.00
Lie-Nielsen No.212 Small Scraper Plane -18tpi Blade LIe-Nielsen Honing Guide Lie-Nielsen No.212 Small Scraper Plane - 25tpi Blade Lie-Nielsen Tool Care Kit

Share your knowledge of this product. Be the first to write a review »